PRECIS support forum

It is currently Mon Oct 23, 2017 10:11 pm

All times are UTC




Post new topic Reply to topic  [ 7 posts ] 
Author Message
PostPosted: Wed Nov 09, 2016 2:11 pm 
Offline

Joined: Mon Mar 28, 2016 5:29 pm
Posts: 17
Dear Users,

I have successfully installed PRECIS2.0 on the Linux distribution openSUSE Leap. However, when I run the Default experiment, nothing happens. The display shows only the message "Not started" (As shown in the attached figure). I checked that only content was created in the umui_runs directory.
I tried to run different experiments, but appers the same message "Not started"

Any idea what's going wrong?

I appreciate any help.

All the best.


Claudia da Costa


Attachments:
imagen.jpeg
imagen.jpeg [ 234.76 KiB | Viewed 367 times ]
Top
 Profile  
 
PostPosted: Fri Nov 11, 2016 9:26 am 
Offline

Joined: Mon Sep 26, 2016 7:30 am
Posts: 11
Dear Claudia,
I am a new member of the support team and don't have an immediate answer for your problem but will consult with my colleagues and get back to you soon.

Regards,

Saeed


Top
 Profile  
 
PostPosted: Fri Nov 11, 2016 12:00 pm 
Offline

Joined: Fri Apr 25, 2014 11:51 am
Posts: 7
Can you try setting up a new region and rerunning?

Simon.


Top
 Profile  
 
PostPosted: Fri Nov 11, 2016 1:13 pm 
Offline

Joined: Mon Mar 28, 2016 5:29 pm
Posts: 17
Hello Saeed and Simon,

Thank you for your prompt reply.

I tried doing this with at least two different areas, however it did not work. The same message appears: NOT STARTED. :oops:

Claudia da Costa


Top
 Profile  
 
PostPosted: Fri Nov 18, 2016 3:29 pm 
Offline

Joined: Fri Apr 25, 2014 11:51 am
Posts: 7
Hi,

You may not have the "at" daemon turned on.

On the command line, can you type

at now

if you see something like:

warning: commands will be executed using /bin/sh
at>

hold down Ctrl and press "D"

If the message is like:

Can't open /var/run/atd.pid to signal atd. No atd running?

You'll need to turn on the at daemon. What short of linux are you using?


Top
 Profile  
 
PostPosted: Fri Nov 18, 2016 4:05 pm 
Offline

Joined: Mon Mar 28, 2016 5:29 pm
Posts: 17
Hello Simon,
I have taken all the steps you have recommended and have obtained the responses you posted.
I'm using the OpenSUSE Leap 42.1.

Claudia da Costa


Top
 Profile  
 
PostPosted: Mon Nov 21, 2016 4:31 pm 
Offline

Joined: Thu Feb 06, 2014 12:29 pm
Posts: 118
Claudia,
TO install the at daemon, try

sudo zypper in at


You then can configure it to be enabled using Yast2 --> System Services (Runlevel).


David


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group